Concrete Repair Products
  • concrete-curing1
  • concrete-curing2
  • concrete-curing3

CRP has a range of concrete curing products that are both proven and effective in the prevention of mosture evaporation in concrete slabs after pouring reducing the risk of cracking and also eliminating the need for ponding, laying of wet hessian bags or wetting of the fresh concrete surface.

CRP'AC'

Download CRP'AC' PDF

Download CRP'AC' MSDS

CRP'AC' is an acrylic modified emulsion used as a curing membrane on freshly poured concrete.

CRP'PRIMECURE 90'

Download CP'PRIMECURE 90' PDF

CRP'BCP' is a blend of bitumen and hydrocarbon resins emulsified in water. The impervious film formed by Evencure BCP prevents excessive water evaporation, promotes efficient cement hydration, minimises shrinkage whilst increasing durability of the concrete

Eco-Cure™

Download CRP'EcoCure' PDF

Eco-Cure™ is an environmental liquid membrane compound manufactured for use on concrete Road and Highway Construction. Eco-Cure™ is the first of its kind and a unique curing compound that does not contain Hydrocarbons like Resins and Mineral Spirits. Eco-Cure™ has been proven to have better performance than the traditional Hydrocarbon based curing compounds.

BENEFITS

  • Environmentally friendly
  • Contains no harmful chemicals
  • Achieves water retention of 90% or greater
  • Increased abrasion resistance
  • Eliminates the need for curing by ponded water,
  • damp hessian or polythene sheeting
  • Reduces concrete dusting and plastic shrinkage
  • One coat application
  • Equipment washable in water
  • May have red fugitive dye added

ADVANTAGES

Eco-Cure™ was formulated to meet the stringent environmental requirements of the "green" construction methods. After 7 years of research and numerous testing procedures Eco-Cure™ was shown to have the following advantages over existing curing systems.

  • No solvents, hydrocarbons or resins of any type
  • No wax or wax based additives
  • No odour before or after application
  • No staining of clothing or equipment
  • No "sticky" residue
  • No environmental problems from residue waste or spillage
  • No "health" issues for personnel
  • No adhesion problems with after trades
  • No discoloration of the concrete surface
  • No blockage of spray equipment

CRP'C30'

Download CRP'C30' PDF

CRP C30 is a wax-based, sprayable curing compound formulated to cure freshly laid concrete. It is a low medium viscosity, white pigmented emulsion of specially blended waxes. CRP C30 meets the requirements of AS3799 for moisture retention in liquid membrane curing compounds.

CRP’FRW’

Download CRP'FRW' PDF

Download CRP'FRW' PDF

CRP’FRW’ is a wax-based, sprayable release agent applied to concrete formwork. CRP FRW is designed to act as a bond breaker between formwork, moulds etc and freshly poured/laid concrete Looking for someone to apply concrete curing agents, dust suppresants, epoxy coatings and specialty compounds? Check out All Surface Coating Pty Ltd (Click the link below)

Uses

CRP'FRW' is suitable as a release agent for construction sites. CRP FRW can be applied to timber, steel or fibreglass moulds and formworks.

CRP’LDH'

Download CRP'LDH' PDF

CRP’L’ Aqueous Solution is a chemically blended aqueous solution, free of chlorides, especially formulated to enhance the properties of the concrete by surface application during curing and after hardening.

CRP’LW'

Download CRP'LW' PDF

Download CRP'LW' MSDS

CRP’LW' is a chloride free, surface applied aqueous solution, especially formulated as a Penetrative Waterproofing Corrosion Inhibitor (for steel reinforcement) that significantly increases the surface hardness of old and new (hardening and hardened) concrete. After application the CRP'LW' remains active in the concrete body to provide in contact with water, self-generative healing properties to seal future hairline cracks.

CRP'EC20'

Download CRP'EC20' PDF

CRP'EC20' is a water-base formulation and environmental alternative to asphalt emulsions. Thus, CRP'EC20' is an alternative to Prime Coats, PCE (Prime Cure Emulsion), AEP (Asphalt Emulsion Prime), prime emulsions, and tack coats (EAP&T). CRP'EC20' membrane forming technology, allows the product to cure, seal, and form a bond in stabilized bases. Unlike traditional asphalt emulsions and tack coats, CRP'EC20' does not contain hydrocarbons or solvent agents like Benzenes, Mineral Spirits, Kerosene, or Petroleum Oils.

CRP X40

Download CRP'X40' PDF

Download CRP'X40' MSDS

CRP X40 is a blend of resins and surfactants emulsified in water and are specially formulated to cure freshly laid concrete. The impervious film formed by CRP X40 prevents excessive water evaporation, promotes efficient cement hydration, minimises shrinkage whilst increasing durability of the concrete surface.

Benefits

  • Complies with Australian Standards AS3799
  • Achieves water retention of 90% or greater
  • Increased abrasion resistance
  • Contains no wax
  • Eliminates the need for curing by ponded water, damp hessian or polythene sheeting
  • Reduces concrete dusting
  • Reduces plastic shrinkage
  • One coat application
  • Can be removed, if required, by ConClena (stripper / degreaser)
  • Equipment washable in water
  • May have red fugitive dye added

Uses

CRP X40 is suitable for curing all freshly laid concrete either smooth or textured, indoors or outdoors.

  • Basement/Substructures
  • Bridge/Road Structures
  • Chemical Protection
  • Dam/Spillway/Hydro
  • Lift Pits
  • Marine Environments
  • Mining
  • Pools
  • Precast
  • Roof/Balconies
  • Sewerage/Reservoir
  • Shotcrete Concrete
  • Sporting/Recreational
  • Tunnels